DIY最後一擊 -- Oyaide RCA和Oyaide Silver XLR Digital

babuwa

I would like to look at the brochure or something like that showing the TECHNICAL DATA of the dire ...
Big_McIn 發表於 2010-7-27 11:45

    The arrow on the skin does show what PCOCC copper direction, If you don't believe you can simply reverse the cable follow the arrow direction against signal flow to hear what the different, Don't believe Technical Data, believe what you hear. I just want to share my own experience.

gundamfix2005

Oh icic

Big_McIn

The arrow on the skin does show what PCOCC copper direction, If you don't believe you can sim ...
babuwa 發表於 2010-7-27 12:00

Hi,

I want to show the way to make a pair of RCA cables with direction flow and point out how to make the END POINTS.

If you connect the shield at the END POINT, you cable does not have diection flow no matter it carries the arrows on the skin or not.

I guess you are using the factory-built product. Then what you have to follow is to look at the arrows. Forget about my suggestion.

If you DIY, I advise you to follow the steps. Otherwise you waste your money.

Finally I would like to let you know that I ,of course, understand how the sound changes if the cables with direction flow connect reversely.

babuwa

Hi,

I want to show the way to make a pair of RCA cables with direction flow and point out how to  ...
Big_McIn 發表於 2010-7-27 12:20

Hello,
Thanks for your advice, since PCOCC are single direction long grain copper,  the signal direction should follow the arrow label on the cable even DIY. Cable shielding is another topic, PCOCC copper itself have direction no matter how cable shield. reverse connection of PCOCC cable will make sound worse.

Big_McIn

Hello,
Thanks for your advice, since PCOCC are single direction long grain copper,  the signal dir ...
babuwa 發表於 2010-7-27 12:45

Hi,

Since Oyaide (Japanese) Cables are printed with arrows and DIY,of course, have to follow them. It's common sense.

However if DIY Current AudioQuest like King Cobra, will feel very painful 'cause can't find any arrows on the outer cloth skin.

So the most important is to know how to make the END POINTS. This is the topic here. Then can make a pair of Directional Single Ended Cables successfully.

That is the experience I want to share here.

babuwa

Hi,

Since Oyaide (Japanese) Cables are printed with arrows and DIY,of course, have to follow them ...
Big_McIn 發表於 2010-7-27 13:16

For DIY, If the cable don't have word or arrow like king cobra, sure no method la, but normally PCOCC cable will have arrow sign, then better to follow la.

Ching's cable are really good handcraft , I'm just DIY power cable only since It's no need soldering.

hooh

其實整RCA時,,開面果層金屬網線,,有冇話最好一定要接落個RCA頭邊個位置,,OR只要接觸到RCA頭就可以

wusum

度身訂造,好fit!,做個朋友哩
本星期我會去試下"搵" 個夾, 買齊材料跟住步驟做條single ended RCA 玩下

Big_McIn

其實整RCA時,,開面果層金屬網線,,有冇話最好一定要接落個RCA頭邊個位置,,OR只要接觸到RCA頭就可以 ...
hooh 發表於 2010-7-27 14:47

要視乎做什麽牌子RCA Plugs和什麽牌子線，尤其是用熱焊方法的時候。

但基本道理就是網線(以Oyaide等日式線為例)不可與正線接觸，線身必須與插身完全接妥，一部份網線要沿外膠套需要剪去。

waicsl

Big_Mcin 兄幫我用啲雞線兩芯線做咗條Directional Single Ended Cable, 好正, 有前有後嫁

喂, 老友, 可唔可以再免費同我整條 AQ KingCobra!