請問各位師兄, 玩Bi-wire係咪會容易燒AMP?

googleli

請問各位師兄, 玩Bi-wire係咪會容易燒AMP?
如果我唔係用Surround Back出玩Bi-wire,
而係齋用Front出,
利用條線本身去到喇叭果邊分開兩邊咁玩 (Sound from Heaven)
係咪會好容易燒AMP? 謝謝.

hohodog900

用surround amp 自己個surround back 出bi-amp 應該好安全，通常都有內部保險，最緊要個Amp set 番bi-amp front。
bi-amp 力水好咗，分別比玩bi-wire 大。

googleli

用surround amp 自己個surround back 出bi-amp 應該好安全，通常都有內部保險，最緊要個Amp set 番bi-amp front。
bi-amp 力水好咗，分別比玩bi-wire 大。
hohodog900 發表於 2009-9-27 09:20

唔該晒師兄!  咁如果唔用Bi-Amp, 只係用Front出, 但係用Bi-wire的話, 會唔會容易燒機? 謝謝!

Beginner

Should be no problem since you just replace the metal bridge with wire.

cmsjkung

請問各位師兄, 玩Bi-wire係咪會容易燒AMP?
如果我唔係用Surround Back出玩Bi-wire,
而係齋用Front出,
利用條線本身去到喇叭果邊分開兩邊咁玩 (Sound from Heaven)
係咪會好容易燒AMP? 謝謝. ...
googleli 發表於 2009-9-27 09:07

Bi-wire and Bi-amp are two different things... For Bi-wire, you need a speaker cable and make it as 2 input to 4 output.. For Bi-amp, you need to use surround back connect to front speaker, remove the speaker jumper, and change the front speaker setting to Bi-amp in AV AMP...

Beginner

Bi-wire and Bi-amp are two different things... For Bi-wire, you need a double run speaker cable and make it as 2 input to 4 output.. For Bi-amp, you need to use surround back connect to front speake ...
cmsjkung 發表於 2009-9-27 11:08

So, my understanding on the configuration is not correct.  Thanks for your information

kennethtcp

Bi-wire and Bi-amp are two different things... For Bi-wire, you need a double run speaker cable and make it as 2 input to 4 output.. For Bi-amp, you need to use surround back connect to front speake ...
cmsjkung 發表於 2009-9-27 11:08

bi-wire 都要 remove jumper, 不過唔 remove 都唔會燒機, 因為實際上你個 output source 都係同一個位, 只係 bi-wire 果時條 jumper replaced by 另一條喇叭線
bi-amp 就一定要飛走條 jumper, 因為個 source 唔同左, 唔飛走條 jumper 會 short 埋兩個 source...  d amp 既 spec 寫就寫有 overcurrent protection, 實際會唔會 trap 我就未試過, 不過有 potential 燒既動作都唔會俾佢發生就得啦

googleli

師兄, 真係謝謝你的解答, 咁如果Bi-wire的話 (不是Bi-Amp) 係咪都係remove jumper好D呢?

cmsjkung

bi-wire 都要 remove jumper, 不過唔 remove 都唔會燒機, 因為實際上你個 output source 都係同一個位, 只係 bi-wire 果時條 jumper replaced by 另一條喇叭線
bi-amp 就一定要飛走條 jumper, 因為個 source 唔同 ...
kennethtcp 發表於 2009-9-27 11:29

Oh.... Forgot to said to remove the speaker jumper for Bi-wire......



Yes, it is better to remove the jumper for Bi-wire, otherwise no point to do Bi-wire....

cmsjkung

My MA RX-8 and RX centre provide better performance using Bi-wire...