英式頭 vs 美式頭 (有咩分別)

djaddy

Djaddy's Evolution & DIY Zone:
http://www.post76.com/discuss/vi ... p;extra=&page=1

Useful sharing by chings on 英式頭 vs 美式頭:

美插:

• 連同認證費用, 生產美插 & 美插電線既成本比英插要低. 所以絕大多發燒級電源線& 拖板出廠時都係用美插而好少生產英插.
• 多個品牌出左 Cryo, 單晶銅 & 單晶銀 wall sockets
• 美插無FUSE, 同埋線同夾線位置接觸面大.  
• 改左美插後, 動態,分析力, 音場, 空氣感等等都有相當的改善.
• 多數都能容納幾粗下o既線.
  

英插:

• 英頭 (wall socket) 只有MK, Clipsal, Sine & IsoClean.
• 飛fuse既英插其實最好聲，接觸穩定 有力量 & 厚度. 在大電流位置上，美頭根本比唔上英頭.
• 多個品牌出左靚聲鍍金鍍銠英插、拖板、fuse、代用fuse.
• 一般Fuse導體用錫,電阻較高, 物料方面同電線用銅 (再鍍貴金屬) 完全唔同,所以音效唔同.
• 英插內部接線接觸面細, 而且內部地方好峽窄, diy 時一個唔小心好容易會N線touch到F線. 所以英插危險過美頭.
• 要買D靚野先夠大入粗線
  

When we consider carefully about UK vs US power plugs, we should use each of these in a combination that will benefit our overall system performance.

For example:
1. Sub-woofer should use 飛fuse既英插 because 接觸穩定, 有力量 & 厚度.
2. Source should use: 美插 because it will improve 動態,分析力, 音場, 空氣感等等都有相當的改善.


Caution:
不過為左"美色" 的o及引, 保險及家居安全亦需考慮.

chingki123

tks c-hing sharing

francis_leung21

咁似乎英插飛FUSE 呢個方安最好....
古河...OYAIDE..等等既日本牌子好似有英WALL SOCKET...

mightyatoms

djaddy, can you teach us how to 飛FUSE? I think not as simple as just remove the fuse in the plug, right?

lskthomas

very useful information.  thank you for sharing!

hkbomberman

It is good to get rid of fuse in British plugs...  How to do so if we can, Master C Hing?

J's

A very well information for me to choosing socket now.

Metropolis

djaddy, can you teach us how to 飛FUSE? I think not as simple as just remove the fuse in the plug, right?
mightyatoms 發表於 2009-12-8 09:16

可以搵另一個英頭既其中一隻腳代替 fuse
借 maner394 兄圖一用


效果好唔好見人見智, 有人話好有人話唔好, 當然隻腳既物料都好大影響

eric8895

多謝分亨

djaddy

飛fuse既英插: I use 派拉利 1.5mm 單支銅代fuse. It's just a little soldering.

I prefer US plug these days. It's much easier & faster to install thick pc's.