pinkspider
發表於 2011-9-26 07:18
而家慢慢煲下先~好似要煲16個鐘~vb個網話~
ricky0706 發表於 2011-9-25 23:12 http://www.post76.com/discuss/images/common/back.gif
vb 網有講煲幾耐咁得意, 完全冇留意過添
pinkspider
發表於 2011-9-26 07:21
由佢寄出到收貨應該8-10日左右。
yard 發表於 2011-9-25 23:17 http://www.post76.com/discuss/images/common/back.gif
我8號order 要23號先到, 可能咁啱多order 等多幾日 {:6_136:}
pinkspider
發表於 2011-9-26 07:27
第一次diy算真係做得幾好啦!!! 好快你又做大師傅架喇!!
其實x25入mk頭算ok, 唔使用ms頭, 你做多 ...
ykluk 發表於 2011-9-25 23:18 http://www.post76.com/discuss/images/common/back.gif
X-25 入到MK 冇問題, 係覺得如果有線再粗少少都入唔到MK 了......
我兩塊白色冚仔都炆走晒添,如果唔炆冚唔返蓋{:6_125:}不過我見上完縲絲都好實, 希望冇事啦
pinkspider
發表於 2011-9-26 07:29
我今日都整左2條5尺,MK頭+瑞士尾加埋都唔使$400
yard 發表於 2011-9-25 23:25 http://www.post76.com/discuss/images/common/back.gif
大家一樣, 快D post 出嚟交流吓丫Ching {:6_190:}
pinkspider
發表於 2011-9-26 07:31
Some Ching said don't use PC or other equipment to run in the cable... 'cause that will 煲死線...
...
wally 發表於 2011-9-25 23:29 http://www.post76.com/discuss/images/common/back.gif
煲死線咁大獲 {:6_200:} 煲死牛就唔驚, 因為我用公司部腦煲 {:6_174:}
ykluk
發表於 2011-9-26 08:28
X-25 入到MK 冇問題, 係覺得如果有線再粗少少都入唔到MK 了......
我兩塊白色冚仔都炆走晒添,如果 ...
pinkspider 發表於 2011-9-26 07:27 http://www.post76.com/discuss/images/common/back.gif
如果你抆走咗嗰兩塊白色冚仔, 能夠hold實條線既只有啲腳既鏍絲, 咁樣會比較危險, 因為x25係散芯線, 其實就算你扭得幾實都好, 始終散芯都會有可能有虛位, 日子耐咗有啲推推撞撞, 都有可能令條線離開鏍絲, 唔好彩啲線掂到其他線咁就short circuit, 所以你最好都係落返兩塊白色冚仔, 係會辛苦啲, 用鉗cut走少少容易啲入!! {:6_142:}
同埋個mk蓋唔係完全入晒好正常, 好多鋪頭幫人整線都會個mk頭離少少, 想實啲就用隻腳踩實啲啦!! {:6_182:}
wally
發表於 2011-9-26 08:48
煲死線咁大獲煲死牛就唔驚, 因為我用公司部腦煲
pinkspider 發表於 2011-9-26 07:31 http://www.post76.com/discuss/images/common/back.gif
Hmm.... put it that way, you use 公司部腦煲線, but end up 煲死牛 or other hardware, caused company lost on hardware or even lost some files... then its your responsibility and you're putting your job into risk because of the cable. So, I think that 大獲 D bor. Currently, if you're the boss, then that's totally different story la {:6_175:}
timmy
發表於 2011-9-26 13:17
我今日都整左2條5尺,MK頭+瑞士尾加埋都唔使$400
yard 發表於 2011-9-25 23:25 http://www.post76.com/discuss/images/common/back.gif
都係外國訂線是嗎?
{:6_211:}
pinkspider
發表於 2011-9-26 13:25
嘩,又一DIY高手出現
kankwan 發表於 2011-9-26 00:29 http://www.post76.com/discuss/images/common/back.gif
DIY 初哥咋{:6_122:}76 D Ching 真係有太把高手就真
pinkspider
發表於 2011-9-26 13:27
如果你抆走咗嗰兩塊白色冚仔, 能夠hold實條線既只有啲腳既鏍絲, 咁樣會比較危險, 因為x25係散芯線, 其實 ...
ykluk 發表於 2011-9-26 08:28 http://www.post76.com/discuss/images/common/back.gif
收到, 睇嚟要再攪攪先得, Thanks for reminder {:6_162:}