正常eSATA係要係電腦關機狀態下，先開Docking再開電腦先認到。
te2370 發表於 2011-8-21 00:16 http://www.post76.com/discuss/images/common/back.gif
已經試過, 都認唔到 eSATA{:5_87:}
回復 1# samnet1
我都用緊此 docking 。 3.5 hardisk 就一直到識別到 ;
但我今天用過新 2.5 hardisk 就吾知點解識別吾到 ............? {:6_141:}
有無 ching help me !
本帖最後由 te2370 於 2011-8-21 00:49 編輯
回復samnet1
我都用緊此 docking 。 3.5 hardisk 就一直到識別到 ;
但我今天用過新 2.5 hardi ...
edlsang 發表於 2011-8-21 00:35 http://www.post76.com/discuss/images/common/back.gif
有冇試過隻2.5"直插電腦認唔認到?
其實我都用過呢隻DOCKING..用左一排我就掉左啦..
已經試過, 都認唔到 eSATA
samnet1 發表於 2011-8-21 00:34 http://www.post76.com/discuss/images/common/back.gif
咁會唔會係個ESATA插有問題呢?
有冇第二D ESATA既野試下插下電腦試試佢
已經試過, 都認唔到 eSATA
samnet1 發表於 2011-8-21 00:34 http://www.post76.com/discuss/images/common/back.gif
Here are some ideas for you:
1. You need to check whether there are proper drivers for your eSATA port for XP.If I remember correctly, XP pre-dates the eSATA standard, so chances are that you won't be built-in drivers for eSATA.
2. IDE drives aren't supposed to be hot-plugged in XP (well, they shouldn't be in general).If you are running XP, chances are that you configured SATA drives as IDE in your BIOS and as a result of that, your eSATA drives are configured as IDE drives.So hot-plug won't work.That should explain why some people suggested that you reboot the machine with the drive plugged in and switched on.No easy fix for that.If you change the settings in your BIOS, chances are that your machine won't boot altogether.
In short, upgrading to Windows 7 might not be a bad idea.And if you do, you should change the settings in BIOS to run SATA drives in ACHI mode.
本帖最後由 samnet1 於 2011-8-21 01:34 編輯
Here are some ideas for you:
1. You need to check whether there are proper drivers for your e ...
qwe456 發表於 2011-8-21 01:08 http://www.post76.com/discuss/images/common/back.gif
you should change the settings in BIOS to run SATA drives in ACHI mode.
==> BIOS 將 SATA 由 IDE set 成 AHCI mode, Boot 唔到機 !!{:5_75:}
已將 Century Manuel upload to #1, 唔識睇日本文 {:5_83:}
you should change the settings in BIOS to run SATA drives in ACHI mode.
==> BIOS 將 SATA 由 IDE s ...
samnet1 發表於 2011-8-21 01:32 http://www.post76.com/discuss/images/common/back.gif
Read my message again."In short, upgrading to Windows 7 might not be a bad idea.And if you do, you should change the settings in BIOS to run SATA drives in ACHI mode."
有冇試過隻2.5"直插電腦認唔認到?
其實我都用過呢隻DOCKING..用左一排我就掉左啦.. ...
te2370 發表於 2011-8-21 00:43 http://www.post76.com/discuss/images/common/back.gif
咦~ 為甚麼呢?!
聽講要安裝window前已在bios set ahci安裝window...........不過我唔肯定
聽講要安裝window前已在bios set ahci安裝window...........不過我唔肯定
cchhll01 發表於 2011-8-21 03:40 http://www.post76.com/discuss/images/common/back.gif
Correct.There are other ways to change it after installing Windows, but a bit painful and risky.
