論壇 › 家庭影院 › 608 bi-wire

kenneth529 發表於 2010-7-7 01:14

608 bi-wire

本帖最後由 kenneth529 於 2010-7-7 01:47 編輯

剛買onkyo608及Klipsch RF-52 想玩bi-wire4出4係應該點插???{:6_141:}
係咪用surr speakers插線位左邊嗰組駁去喇叭上面嗰個插線位就得???Amp需唔需要set嘢架???
望ching幫手~~{:6_139:}
THX~~

maner394 發表於 2010-7-7 04:55

本帖最後由 maner394 於 2010-7-7 05:00 編輯

SURR BACK OR FRONT HIGH OR FRONT WIDE L==> speakers Tweeter (high)
SURR BACK OR FRONT HIGH OR FRONT WIDE R==> speakers Woofer (low)
http://filedepot.onkyousa.com/Files/own_manuals/SN29400239_TX-SR608_En_web.pdf?CFID=1093684&CFTOKEN=20066409&jsessionid=f030dfae1091fe9f7695317d3137175c6373(608 說明書)
• Powered Zone 2 cannot be used if “Speakers Type” is set to
“Bi-Amp” (➔ 56)

kenneth529 發表於 2010-7-7 10:29

Thx~maner ching.{:1_335:}

24105 發表於 2010-7-7 10:57

this is "Bi-Amp" {:6_193:} setting as mentioned by the above C-hing

七彩小生 發表於 2010-7-7 11:50

本帖最後由 七彩小生 於 2010-7-7 11:51 編輯

比我多數拿走哂有關的喇叭線, 先config好 onkyo bi-wire or bi-amp, 然後power off, 再駁番{:6_239:}

yoes 發表於 2010-7-7 12:12

CHing記得係speaker setting改為"bi-amp", 並將speaker高/低頻插頭之間銅片拿走, 唔係好易燒喇叭{:6_182:}

avhunter 發表於 2010-7-7 12:56

SURR BACK OR FRONT HIGH OR FRONT WIDE L==> speakers Tweeter (high)
SURR BACK OR FRONT HIGH OR FRONT ...
maner394 發表於 2010-7-7 04:55 http://www.post76.com/discuss/images/common/back.gif
好詳細 {:1_351:}

yoes 發表於 2010-7-7 13:36

Kenneth 兄諗住用咩線??
會唔會試高低頻唔同線較音質??{:6_235:}

kenneth529 發表於 2010-7-7 17:14

CHing記得係speaker setting改為"bi-amp", 並將speaker高/低頻插頭之間銅片拿走, 唔係好易燒喇叭 ...
yoes 發表於 2010-7-7 12:12 http://www.post76.com/discuss/images/common/back.gif

原來高/低頻插頭之間有塊銅片架，返去睇睇先。thx~

kenneth529 發表於 2010-7-7 17:24

Kenneth 兄諗住用咩線??
會唔會試高低頻唔同線較音質??
yoes 發表於 2010-7-7 13:36 http://www.post76.com/discuss/images/common/back.gif


    其實我係新手嚟，都係d嘢啱啱送嚟。我都係聽兇宅哥哥買咗ultralink試吓，佢話會好聲d。查實我都唔係好識.
{:1_263:}
其實bi w-wire睇戲有無分別？

查看完整版本: 608 bi-wire