chhanthony
發表於 2016-10-20 14:33
yuppi 發表於 2016-10-20 14:22 static/image/common/back.gif
http://www.indyaudiolabs.com/products/
Yes, 同公司, Acurus is for AV.
你攞嚟做啦
chhanthony
發表於 2016-10-20 14:35
Large room loudspeaker layouts up to 7.3.6 or 9.3.2 are supported. (咁得意嘅)
yuppi
發表於 2016-10-20 14:39
chhanthony 發表於 2016-10-20 14:33 static/image/common/back.gif
你攞嚟做啦
問緊新加坡代理, 佢地響香港有分公司
不過部機要另外買呢套野, 吾識玩.......{:6_203:}
http://www.daytonaudio.com/index.php/omnimic-v2-precision-measurement-system.html
chhanthony
發表於 2016-10-20 14:40
yuppi 發表於 2016-10-20 14:39 static/image/common/back.gif
問緊新加坡代理, 佢地響香港有分公司
不過部機要另外買呢套野, 吾識玩.......
Omnimi + pc
EQ Process Steps
To use the built-in EQ in the ACT 4 to tune a home theater room, the following general process is used:
1) Locate the MLP in the room and place a measurement microphone in that position at ear height. 2) Determine a frequency range for optimization.Generally this
range will include the lowest frequencies though to some mid-frequency.Assuming reasonably flat loudspeakers and average room acoustics, frequencies above, say, 8kHz or so can and should be left alone. 3) Ensure that the ACT 4 speaker parameters are set properly for
the size of each speaker (small vs large) and that delays for each are set according to the physical distance between the loudspeaker and the MLP.
4) Use the PC to analyze and EQ each front, center, and subwoofer loudspeaker using the measurement mic and Omnimic software.The target curve is set to reduce audible response peaks, not to boost nulls or dips.
5) Analyze and EQ audio bed surround and overhead speakers (optional) 6) Analyze and EQ the overall composite response of all
loudspeakers using the ACT 4 global high and low frequency shelf filters.
7) Copy the filter values for the optimized response curve (frequency, gain, Q) to the ACT 4 from the Omnimic application. 8) Finally, check and make any necessary adjustments to the
resulting EQ in the ACT 4 with a variety of signal sources.
yuppi
發表於 2016-10-20 14:40
chhanthony 發表於 2016-10-20 14:35 static/image/common/back.gif
Large room loudspeaker layouts up to 7.3.6 or 9.3.2 are supported. (咁得意嘅)
新 firmware support 7.3.6, 6 ceiling speaker for Large room
yuppi
發表於 2016-10-20 14:41
chhanthony 發表於 2016-10-20 14:40 static/image/common/back.gif
Omnimi + pc
EQ Process Steps
吾識......{:6_202:}
chhanthony
發表於 2016-10-20 14:41
yuppi 發表於 2016-10-20 14:41 static/image/common/back.gif
吾識......
學............
yuppi
發表於 2016-10-20 14:44
chhanthony 發表於 2016-10-20 14:41 static/image/common/back.gif
學............
年紀大, 入吾到腦.....
部機咁貴, 買到先算....{:6_194:}
chhanthony
發表於 2016-10-20 14:46
yuppi 發表於 2016-10-20 14:44 static/image/common/back.gif
年紀大, 入吾到腦.....
部機咁貴, 買到先算....
老實個牌子畀我嘅印像係出開affordable product,如果USD8500真係有點兒過火。
yuppi
發表於 2016-10-20 14:48
chhanthony 發表於 2016-10-20 14:46 static/image/common/back.gif
老實個牌子畀我嘅印像係出開affordable product,如果USD8500真係有點兒過火。 ...
under $40k 即入 (個人妄想){:6_176:}