WSC 黑騎士 Vatshu The Black Knight 五星物語 製作進度
本帖最後由 大佬John 於 2016-2-21 02:15 編輯呢排睇多左AOA果D韓妹, 單手砌砌下就諗多左野
研究企pose,股位脊骨,手臂線條, 亦係砌完Gastness Temple之後感想
WSC D股位, 膝同腳眼都係freepose, 有時見set反膝過份
以下探討何謂"S"立, 純綷自己搜集見解, 會同坊間既觀念離地, 只係我係咁睇法。友人質疑:個個廿幾年都係咁砌, 係得你唔同, 唔通你叻D?! 其實我係諗住細個果時行入機舖, 睇人出升龍拳, 係則邊睇住學, 見佢隻手向後咁打圈, 同學之間就開始傳 '向後打細圈' 既秘技。 因為個個都盲摸摸, 自然要多撞板先會出到一次升龍拳。
如果有人話俾班小學雞知, 其實個指令係 ↓\→ ↓\→ 拳, 咁人人有普練功咪好快學成呢囉。
依我觀察, 改高達有一種 凸 jer jer既"S"立
從下圖可見, 盤骨或褲頭水平向後斜, 脊骨變成肧胎咁捲起
https://farm1.staticflickr.com/753/20514592144_3f3e9c6fa7_n.jpg
從時裝角度, 著高踭鞋既作用, 係令蘿pat翹起, 脊骨變得更S形。
最左邊係平底鞋, 中間著左高踭鞋, 盤骨水平向前斜落, 蘿pat翹起, 凸肚, 肩拉後(紫色線), 並冇凸 jer之效, 盤骨水平亦冇向後斜。
右邊我加左上面nu高達果種盤骨向後斜(紅線)的縮肚凸 jer jer pose, 脊骨變成肧胎咁樣捲起。
https://farm6.staticflickr.com/5672/21137242005_d2fa0117d7_n.jpg
觀察林浩己figures同眾多女囡, 可見女體除左以上提到的翹蘿柚, 凸肚, 肩拉後之外, 膝頭有少反屈, 大腿前面線條是15至20度的斜線(春麗可能會勁D), 呢樣我理解成五星反膝在視覺上既功能。 純綷o係網上先量化咁講幾多度。(睇咁多女都係白睇啦)
http://i602.photobucket.com/albums/tt107/ingenhk/Homepage/wf00201d.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Homepage/8538.jpg
我件Gastness同黑騎只係反膝15-20度, 見肩,肚,蘿柚,大腿 D線條都OK唿合。(由膊頭至腳眼,不計頭同腳掌)
http://i602.photobucket.com/albums/tt107/ingenhk/Gastness%20Temple/ceaf1bfe-3fe4-4a25-a053-078d7e7fd072.jpghttps://farm2.staticflickr.com/1624/24044309229_af39d25380.jpg
股位移前既用意, 幾乎肯肯定, 係為左將腹部比堅尼位同大腿前連成一線, 麻甩Hard Gay的凸 jer jer不是主調。綠色線已經係S字, 不用將對腳猛抽後。
http://i602.photobucket.com/albums/tt107/ingenhk/Homepage/figure2.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Homepage/wf00102.jpg
常見為左拗多D曲線, 反膝腳抽後多D令到佢多D凸 jer。
大腿成30度的例子,視覺上似凸 jer多過似凸肚, 翹蘿柚線條被中和抵消。而且角度突然, 似"Z"字多過"S"字。
http://i602.photobucket.com/albums/tt107/ingenhk/Homepage/wf00103.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Homepage/8279.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Homepage/4826.jpghttps://farm6.staticflickr.com/5650/20950459789_7950b41300_n.jpg
WSC多厚身立體不能格硬拗大S字, 反膝太多又會矮左, 尤其WSC正常長度沒有過份長腳。
左圖可見上身至股位長度一樣時, 對腳長度可以差咁遠
https://farm2.staticflickr.com/1616/24360675275_15ff436d86_n.jpghttps://farm2.staticflickr.com/1550/24296389505_67317e5235_n.jpghttps://farm2.staticflickr.com/1441/24270236006_981dbedcb0_n.jpg
用類似cranial units既方法, 將拳頭至膊頭分成4個圈圈, 不計手指。正常比例, 條腳應該有6個圈圈。
左邊既Gastness反膝30度頂前股腳抽後, 腳只得5個圈, 矮左足足1個圈。
右邊係我既, 有6個圈, 就算高炒都唔會矮好多。
https://farm2.staticflickr.com/1653/24044509729_103f2f0473_n.jpghttps://farm2.staticflickr.com/1468/24329773021_e3cf5e5d9d_n.jpg
腳抽後又會令到裙尾黐住對腳, 見唔到翹蘿柚, 比較下圖粉紅色空間和大腿角度。
https://farm1.staticflickr.com/742/20514592404_7d36e1b9a6.jpg
入正題, Set 黑騎腳
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5178.jpg
通常的手臂硬直
https://farm2.staticflickr.com/1551/24318417845_de7626ebbf.jpg
呢幾part好多時見推貼晒黎set, 就會似打石膏
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5190.jpg
針對硬直線條搞搞佢
http://i602.photobucket.com/albums/tt107/ingenhk/Homepage/8988.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Homepage/9068.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5228.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5226.jpg
隙位用曲手optional part磨細改入去
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5206.jpg
腳腕移開, 喇叭腳順返D冇咁突然
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5265.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5266.jpg
校對稱
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5147.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5180.jpg
後面棟起塊cutting mat, 用上面D格仔睇對稱
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5253.jpg
呢個pose係set左十次左右先接近滿意
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5301.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5291.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5311.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5300.jpg
個盾舉出膊頭甲以外, 向下少少, 但拳頭曲上, 如果拳頭曲入就會好似好用力咁舉個盾(攰look)。盾太貼身又怕似只顧防守唔進攻咁(turtling)
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5293.jpg
開窿之後, 用顏色印去另一邊
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5156.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5170.jpg
入兩條銅支, 平行, 分開少少
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5157.jpg
另一邊刨鬆佢 (一邊緊, 另一邊鬆)
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5177.jpg
CA膠同AB膠, 建議用軟身D(圖中呢隻有D硬), 或原子灰
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5136.jpg
滴CA膠(少少)入去, 茶個窿內壁, 再塞入AB膠/ 原子灰, 之後印落去另一邊, 等乾
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5139.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5348.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5349.jpg
膊頭, 胸下面呢D罅
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5363.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5364.jpg
搓一條幼長epoxy
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5367.jpg
茶CA膠o係條邊度, 圍上去
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5368.jpg
另一邊茶爽身粉, 之後印落去
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5373.jpg
等硬
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5370.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5375.jpg
係咁易修下之後
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5379.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5381.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5382.jpg
高低級分模線
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG0994.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1000.jpg
要填左佢先, 唔可以就咁削
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1004.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1008.jpg
背脊呢兩塊, 就咁set會唔對稱
https://farm2.staticflickr.com/1569/24323170539_9f826446d4_z.jpg
攪一攪
https://farm2.staticflickr.com/1590/24597356131_5245827d64_z.jpg
其他對稱/平衡
https://farm2.staticflickr.com/1625/23765956264_42c1fbcd1c.jpghttps://farm2.staticflickr.com/1534/24367937446_f9b8a2cea8.jpg
腳掌再set過改善貼地/鬆(唔駛橡筋), 結果膝股等要set過晒, 依家結構受力位都好實.
另外上左甲之後, 將對手臂貼近身DD。改善之前睇落太橫, 令到個頭睇落好窄等問題, 不過側身冇咁型仔。
新舊對比(左係新), 會將個盾轉去側面少少, 至到正面見到整條手臂內側線條, 由格肋底至手指公, 同時露出成套裙甲, 唔會摭左一角。
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5388.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5337.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5390.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5342.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5391.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5331.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5392.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5339.jpg
裙尾呢條邊應該同褲頭一件過, 不過用印位去處理
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5378.jpg
其他細粒件印位
腰兩側
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1014.jpg
劍
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1017.jpg
膝後
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1015.jpg
順便提下, 之前膝位跟巴爸咁set, 但原來佢後移左少少, 膝後果塊蓋拍唔埋, 改正前後
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5159.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5178.jpg
手下臂兩條喉, 風筒吹熱將佢地收緊D, 上次砌完Gastness Temple, 覺得D喉破壞線條, 今次唔俾佢凸出黎, 視覺上似兩條筋肉包住手臂咁。
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1022.jpg
上臂連住膊頭既喉, 試位之後裁走三格
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5406.jpg
諗住睇下留長少少等佢下垂DD, 不過唔鐘意格肋底下面太多虛位
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5408.jpg
再裁走四格, 只剩低15格
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5420.jpg
上. 19格長D垂低, 下. 15格緊D貼身
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5403.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5419.jpg
我會想象膊頭, 格肋底, 上臂既佈局, 條喉就係果一點
http://i602.photobucket.com/albums/tt107/ingenhk/Homepage/8632.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Homepage/8631.jpg
所以緊D好睇D, 又有似肌肉線條既觀感
鬆
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5405.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5401.jpg
緊
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5414.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5415.jpg
上晒D甲, 條喉剛剛係背後塊甲既邊沿, 睇落密度更高
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5410.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5411.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMG_5418.jpg
強勁手臂線條
https://farm2.staticflickr.com/1480/24727871659_60f26b83bf.jpg
膊頭甲入面有幾條線太淺, 但又頂住左, 搵支針磨尖再屈起入去刻, 不過好唔就手, 刻得麻麻地
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1028.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1024.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1030.jpg
股位, 膝後呢幾處唔sharp, 好似張相out focus咁, 只係刻少少, 刻到夠sharp去滲線就OK
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1031.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1032.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1033.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1035.jpg
{:1_351:} CHING 簡直係神級專家! 堅正 post {:1_351:} 快啲砌完噴完成品吧，好心急想睇你的大作品{:6_157:} {:6_136:}超級工程{:6_193:}
完美無凡.......得得得
果然係一個研究生 {:6_121:} {:6_126:} {:6_128:}
{:6_193:} {:6_195:} {:6_178:} 好勁~ 以前都係TOYSDAILY見過大師砌 破烈之人偶~
真係以為自己都可以砌得咁勁!!!
好羨慕~!!! up一up先, 魷魚之處理
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1100.jpg
沿紅色啄開一條直線
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1100b.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1101.jpg
之後再補Epoxy, 補完再輕輕坑一條幼線出來
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1100b.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1107.jpg
好細好密氣泡唔識攪
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1092.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1093.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1094.jpg
粒珠矇(左)約0.5mm, 簡單做法的話, 直接剷走再植0.5mm鋼珠。
不過我冇錢, 又唔想搭車出去買, 所以就咁勾佢出來
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1108.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1112.jpg
腳擋下唇近邊位有D彎, 見圖陰影所示。將來上半光澤, 呢塊45度向上對住天花板, 見到反光彎入去會好覺眼。
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1119.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1120.jpg
修正
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1122.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1124.jpg
腰側邊有少少高低級, 一般CA+粉補法
冇特別去刮深線, 只係將腰一層層級位之間既Ｌ形刮清楚, 等上色之後可以慢慢'劃'D線出黎
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1129.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1130.jpg
難磨既位用毛鉗夾住, 捲起一個圈仔咁入去磨
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1139.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1145.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1134.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1140.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1132.jpghttp://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1141.jpg
http://i602.photobucket.com/albums/tt107/ingenhk/Vatshu/IMAG1144.jpg
頁:
[1]
2